Now that my control panel is mostly done, I’ve been trying to figure out
the best way to lay out the wiring inside to keep it tidy and organized.
There are lots of individual circuits, so I decided to use a grid style PC
board for the components, such as the bridge rectifiers and the
resistors.
I realize that I could have probably cut down on the amount of resistors I
used. However, I opted to keep a resistor for each individual circuit to
keep the wiring as close as possible to my original plan. I’m sure there are
several different ways this system could be wired, this is just one of them.
I used my soldering iron to attach the components directly to the PC board.
I will then eventually attach all my wiring to the back of the board to each
appropriate component.
Since my last update, I have been working almost daily on my new control
panel. I have also finished the wiring plan and schematic for all of the
switches and electronics. The plan includes the wiring for the control
panel, all lighting and signals, switch machines, power blocks, and
under-table wiring. I have been working and modifying this electrical plan
for quite some time now and though it looks quite complex, it’s actually
quite simple. It just looks like a lot because it shows absolutely every
circuit. Some of this is already wired, such as the under-table switches,
but the majority of it will be in my control panel.
As for the control panel, it has been quite a learning experience with a
lot of trial and error, blood and frustration. In the end however, the
almost-finished product turned out pretty good.
I planned the control panel to be a box-style panel, with all the lights
and switches on top and all wiring and electrical components stowed inside.
I decided to use 1/4” hardboard to construct the controller. Like always, I
first made a detailed plan on paper of what I wanted to build. This makes
things so much easier when it comes to construction. After drawing out the
panel pieces on the hardboard, I used a jigsaw to carefully cut them out. I
then glued them together with Weldbond white glue.
Once the glue had cured, I measured and cut out the holes for the voltage
meters. These meters will eventually monitor the CAB 1 and CAB 2 outputs
from my power pack. I decided to go with analog gauges instead of digital
ones for a more of a traditional look.
I was originally planning on painting my control panel, however I realized
that paint was not going to be enough to cover many of the imperfections. I
decided to cover the box with recycled black and wicker aluminum cladding
from a scrap yard. I was not able to bend the cladding well enough to cover
the box, so I cut individual pieces for all 5 sides.
Cutting holes through the cladding for the voltage meters proved to be
quite the challenge as I didn’t have the right tools to cut a perfect
circle. Instead, I used a small drill bit to drill several dozen holes
around the traced circle. I then re-drilled these holes with a larger bit
until the holes joined and the center circle fell out. With a bit of
modification and filing, it fit perfectly over the control box
holes.
Using PL Ultimate construction adhesive, I attached 1/2” steel L-molding to
the edges and corners of the panel, giving it a finished look. The finished
panel turned out better than I expected, though there are some noticeable
imperfections. At this time I also installed all of my Atlas switches on the
face of the control panel.
Next I installed the controller components onto the face of the panel using
small screws. For these, I used an Atlas Controller, three Atlas Selectors,
and four Atlas Switch Control Boxes. The Controller will allow me to reverse
direction on both CAB 1 and CAB 2, as well as select which CAB controls the
turntable. The selectors will control the twelve power blocks on my layout
and the four switch control boxes will switch the track turnouts. See the
Wiring Diagrams
page for detailed explanations of how all these components work.
The next item for construction was the display for the turnout positions as
well as the 13 track power blocks. I decided on two separate diagrams;
one for the overall layout and one for the turnout points. This kept the
diagrams much less cluttered and easy to understand. I cut frames for each
diagram out of 1/16” craft wood board and stained it dark ebony.
For the diagrams, I used digital vector images I created in Photoshop
instead of using the traditional tape method. I printed these images on
photo paper and glued them to the back of the wood frames. I then fastened
the frames to the face of the control panel with PL Ultimate adhesive. The
numbers on the diagrams correspond to the switch numbers and the power
blocks.
Next I drilled holes through the switch position diagram and installed my
LED lights which will indicate the switch positions; red for the turnout and
green for the main line. Switches 1-3 are all for the main line yard and
switch 4 is for the turnout to the turntable. I also drilled holes for the switch and accessory indicator lights, such as
layout and power LEDs.
The yellow LEDs at the top of each Atlas switch are for switch machine
overload protection. I’ve heard that Atlas switch controls sometimes stick
and will burn out switch machines so I added this little feature that will
indicate a stuck switch. The LED will light only for the moment that the
switch is pressed. If the switch sticks, the LED will stay lit, indicating
power overload. You can see how I wired these in the wiring schematic at he
bottom of this post.
Once everything was attached, I started to label all of the Atlas
controllers, switches and selectors. The numbers that were included with the
switches didn’t fit correctly nor did they look good, so I constructed my
own in Photoshop. I opted for a black background and white text, making them
blend perfectly with the Atlas switches. Once printed, I cut out each letter and number and stuck it to each switch
using double sided tape.
I will still need to label the rocker switches and some of the other LEDs
on the control panel, but I'm pretty happy with how this turned out so far.
The next step will be all of the wiring. The control panel will eventually
be mounted to a piece of plywood with the cab controller right beside it.
The final plan is to have the entire unit fold away under my layout when not
in use.
I have now installed four new Atlas under-table switch machines, one Atlas
trackside switch machine, and a new motor for my Atlas turn table. I have
also been collecting the various parts and components for the control panel
that I am designing. I still need four Atlas snap-relays as well as the dual
cab MRC controller I’ve had my eye on. I will have more details on this when
I get a more finalized plan on its design.
The under-table switch machines installed pretty easily, with only a few
adjustments needed. The hardest part was keeping them positioned while
screwing them in. A partner definitely helps with this step. One issue that
did need some attention was the ease of movement of the turnout itself. The
switch machine motors themselves are pretty powerful, especially with a 16V
AC burst of power. However, the issue comes from the very small distance of
the switch machine's movement as well as the slight flexibility of the
plastic pin that attaches to the track switch point.
The switch machine's movement is just barely longer than the distance of
the turnout point itself. This means that there is very little room for
error when installing the switch machine as it needs to be installed
perfectly centered with the turnout. Also, because the small pin that moves
the switch point has a bit of flex, ANY resistance in the track switch point
will prevent it from fully engaging. Because of this, I ended up having to
remove the roadbed under the sliding bar of the turnout to ensure there was
no resistance. After a few adjustments, the track turnout moved much more
easily and everything worked fine.
As for the wiring, each switch machine will be on an independent Atlas
switch controller; green wire being for the main line and yellow being for
the turnout. All are grounded by a common wire which is the center brown
wire. Switches 2 and 3, which branches from the main line to the front spur,
are on a common switch and operate in unison as they will always need to be
switched together when crossing off of or onto the main line.
Unfortunately, I was not able to install an under-table switch machine to
the turnout to my turn table. Because of this, I had to use a trackside
switch machine. I wired it just as I did with the under table switch
machines and attached it to the same brown common lead. I will have to find
some way to hide this machine in the future. I have also attached my new
turn table motor. It works great, but is a little loud. Hopefully this will
be quieted slightly when the cover is attached. With that, there is where I
am this rainy Wednesday evening.
I’ve now started the planning stages of the main control panel and wiring
and have purchased more than half of the components. I plan to build the
unit out of wood, covered in aluminum cladding. I’m still not entirely how
it will look, but I’m going for an all-in-one unit with all of the switches,
lights, and wiring, which will fold somehow under to table to hide away when
not in use. I’ve also painted the turn table to make it look a little more
realistic. I also stained the trestle a dark, rich brown colour. I used a
toothpick to paint on little bolts.
I have also completed further testing and all the layout works great. The
locomotives and rolling stock I currently have are not the best quality, but
they run well enough that I can test my track and turnouts and find any
errors.
The track on my layout is 99% complete, with just a few small items to
finish. I have almost completed the turn table, however it still needs to be
painted to get rid of the plastic look. Spur track will be added once it's
complete and permanently installed. I also painted and installed the track
bumpers, five in total on my layout. They look pretty decent, however they
may need a little more detail added in the future. My turnouts also look and
fit great. I tested them with a few cars and they see to carry rolling stock
very smoothly
I’m still not sure how the descending grade from the trestle is going to
work out with a full set of cars and engines. It’s very steep as it needs to
drop down 3.5" in a very short distance so it can level out at the track and
road crossing.
This is the one part of this whole project that has me worried. At this
point the layout is divided into the planned 12 electrical blocks using
insulated terminal joiners between the sections of track. I have also
attached all terminal connectors, feeding the wires through drilled holes to
the underside of the table.
Tomorrow I plan to paint the turn table to make it look a bit more
realistic and finish attaching the approaching tracks. The big project now
is to start the wiring and construction of the control panel. The
under-table switch machines and wiring components also need to be done at
this point. I also need to test my track with an engine, so for now I will
need to attach all the terminal connectors from each power block to one main
lead, just to test things out. That will be a next weekend
project.
I’ve spent most of the time since my last update working on attaching the
track to the roadbed, as well as installing the terminal connectors to
isolate each of the twelve track sections. I have not yet attached the track
to the trestle or bride as they still need to be finished with paint and
stain first.
I've measured the space for my four remaining turnouts at least 10 times to
make sure they will fit, along with other assorted Atlas track pieces. I
will attach these last as I want to complete the rear sections of track
first and not have to lean over the delicate switches.
At this time I have also laid the descending track from the trestle to the
60 degree crossing. This part of track worries me. I have tested this with
an old Canadian Pacific engine and it works fine, however it does not look
prototypical and I haven’t tested it with cars. I will just hope for the
best at this point.
The inner figure-8 track is now mostly complete, leaving the outer main
curve and front staging area as the last sections of track that need to be
completed. The outer main loop will be flex track. I also installed Atlas
track bumpers at the end of my spurs.
For the terminal connectors that attach the power leads to my track
sections, I soldered a wire lead to the bottom of metal track connectors
then installed them to the control rain of each section. I then ran the wire
lead through small holes that I drilled through the benchwork right below
the connector. They are almost impossible to see.
I will be working on the remaining track and start wiring during the next
few weeks. Under-table switch machines, the turn table, and the control
panel are also on the list for things to start working on.
Last weekend I purchased my five Atlas turnouts, a 60 degree crossing, and
some other track pieces from PM Hobbycraft in Calgary. I now have almost all
of my track other then the turn table and a few pieces that aren’t part of
the main lines. Now that I have my exact measurement and can see exactly how
the track is going to sit, I completed the rest of the roadbed for the front
staging area as well as the lead to the future turn table.
After a week, I finally completed my trestle. I built it using 1/4” and
3/8” square doweling rod purchased from a local hardware store. I first
traced on a large sheet of paper the track curve, as well as the location of
the tracks that would pass below. From this, I determined the measurements
as well as the location of each pier.
I built the deck of the trestle directly onto the drawing that I had made,
using this as an exact guide for placing the pieces. This was the best
option to keep everything accurate. The piers had to be on a sharp angle due
to the two tracks passing below so extra support had to be given to the
trestle deck in some areas. I finished the piers with 1/16" cross supports
as well as a deck for the 18" radius track to sit on. Even thought this is
not the most prototypical trestle, it still looks good on the layout and
fits the track perfectly.
By this time I have placed all of my track bed with the exception of the
front staging area. I just want to be sure of my turn out positions before I
glue anything down permanently. You can finally get a good idea of how my
layout is going to look.
On my last day off, I added the trackbed for the upper mountain tunnel
lines. The outer track is part of the main oval line, which will descend
down to the front staging area. The second ascends up from the track
crossing in the center of my layout to the raised area at the rear of the
layout. This line and the main line run together in one tunnel portal. I
have also laid the track through the lower tunnel portal . I completed this
so I wouldn't have to work around the upper sections of track in the
future.
This wraps up my Canada Day long weekend. My plan for the following week
will be to get a good start on the large wooden trestle.

















































